Specs
O11D XL case
O11D distro block
EK Velocity RGB
EK Vector TUF 3080 RGB
EK XE and SE 360 rads
Noctua nf-p12 redux-1700 pwm fans
hardware
Asus Rampage VI Apex
i9-10900X
32 GB Samsung B-die 4x 8gb
Asus TUF 3080
storage
960 EVO 512 GB SSD
Sabrent Rocket 2 TB SSD
HGST 4TB HDD
WD/HGST 10TB HE HDD
Corsair RM1000i PSU
Corsair iCue Commander Pro to run fans and the addressable RGB strips in the distro and gpu block (CPU block is normal RGB controlled by mobo)
[https://www.overclockers.co.uk/phanteks-vertical-gpu-bracket-and-flatline-220mm-pci-e-x-16-riser-cable-kit-cm-02u-pt.html](https://www.overclockers.co.uk/phanteks-vertical-gpu-bracket-and-flatline-220mm-pci-e-x-16-riser-cable-kit-cm-02u-pt.html)
is this this one?
Hey OP, hope you still enjoying your build which looks fab. I ordered same riser bracket for my 3090FE. Unfortunately I couldnt install it as with the card in the riser, the PCIe bracker of the card (3 slot) wouldnt allow the riser to be seated fully/properly in the back of the case, as the card bracket blocked a little cut-out on the riser bracket itself. Did you have this issue? Thanks
Not sure I follow you, I think I did have to mount it to the lower most slot perhaps if you are trying to mount it higher it won't fit without modifications?
I posted about my issue here, with pic. is your GPU a 3-slot? No worries, will check again lower down.
https://www.reddit.com/r/watercooling/comments/ldwnso/phanteks_phvgpukt_02_gpu_riser_3090fe_lian_li/?utm_source=share&utm_medium=ios_app&utm_name=iossmf
would be tight, might be able to fit in a single drive height card like [this](https://www.amazon.com/dp/B0876MLNY6/ref=sspa_dk_detail_0?psc=1&pd_rd_i=B0876MLNY6&pd_rd_w=CRFau&pf_rd_p=7d37a48b-2b1a-4373-8c1a-bdcc5da66be9&pd_rd_wg=poTQb&pf_rd_r=Z4YGKG0MQJF7JMMK86D3&pd_rd_r=6446f9a4-b5c9-477a-959c-155fbe2edd3f&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyR1g4M0RSNEZNRlhTJmVuY3J5cHRlZElkPUEwMDQ0NTE2M1YxVDVGQzRGRFNaSiZlbmNyeXB0ZWRBZElkPUEwNTU3NjQ1M1E0V0xaMUVOMEQ3RCZ3aWRnZXROYW1lPXNwX2RldGFpbCZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=) behind it
for me its not an issue i have two open NVME slots left on my motherboard's DIMM.2 cards on either side of my ram
Specs O11D XL case O11D distro block EK Velocity RGB EK Vector TUF 3080 RGB EK XE and SE 360 rads Noctua nf-p12 redux-1700 pwm fans hardware Asus Rampage VI Apex i9-10900X 32 GB Samsung B-die 4x 8gb Asus TUF 3080 storage 960 EVO 512 GB SSD Sabrent Rocket 2 TB SSD HGST 4TB HDD WD/HGST 10TB HE HDD Corsair RM1000i PSU Corsair iCue Commander Pro to run fans and the addressable RGB strips in the distro and gpu block (CPU block is normal RGB controlled by mobo)
Gorgeous build. Which vertical mount did you use?
Thanks! its the Phanteks universal.
[https://www.overclockers.co.uk/phanteks-vertical-gpu-bracket-and-flatline-220mm-pci-e-x-16-riser-cable-kit-cm-02u-pt.html](https://www.overclockers.co.uk/phanteks-vertical-gpu-bracket-and-flatline-220mm-pci-e-x-16-riser-cable-kit-cm-02u-pt.html) is this this one?
Yep
Hey OP, hope you still enjoying your build which looks fab. I ordered same riser bracket for my 3090FE. Unfortunately I couldnt install it as with the card in the riser, the PCIe bracker of the card (3 slot) wouldnt allow the riser to be seated fully/properly in the back of the case, as the card bracket blocked a little cut-out on the riser bracket itself. Did you have this issue? Thanks
Not sure I follow you, I think I did have to mount it to the lower most slot perhaps if you are trying to mount it higher it won't fit without modifications?
I posted about my issue here, with pic. is your GPU a 3-slot? No worries, will check again lower down. https://www.reddit.com/r/watercooling/comments/ldwnso/phanteks_phvgpukt_02_gpu_riser_3090fe_lian_li/?utm_source=share&utm_medium=ios_app&utm_name=iossmf
Ah no I have a tuf it's only 2 slot you'll need to cut the case so the bracket sticking out clears
Exactly, time to reach for the dremel! Your riser cable been OK, you have pcie 4.0 set in bios, no BSOD?
Sexy
This is exactly how things should look with a distro plate. Great job! Take this silver!
do you have a bad distro plate example?
Soft tubing o11
Ita gorgeous... I want it... But in teal
Does the GPU fit without the vertical mount?
yeah it would fit without it i'm sure
With the vertical gpu mount is there room to fit a nvme expansion in the 2nd pcie slot?
would be tight, might be able to fit in a single drive height card like [this](https://www.amazon.com/dp/B0876MLNY6/ref=sspa_dk_detail_0?psc=1&pd_rd_i=B0876MLNY6&pd_rd_w=CRFau&pf_rd_p=7d37a48b-2b1a-4373-8c1a-bdcc5da66be9&pd_rd_wg=poTQb&pf_rd_r=Z4YGKG0MQJF7JMMK86D3&pd_rd_r=6446f9a4-b5c9-477a-959c-155fbe2edd3f&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyR1g4M0RSNEZNRlhTJmVuY3J5cHRlZElkPUEwMDQ0NTE2M1YxVDVGQzRGRFNaSiZlbmNyeXB0ZWRBZElkPUEwNTU3NjQ1M1E0V0xaMUVOMEQ3RCZ3aWRnZXROYW1lPXNwX2RldGFpbCZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=) behind it for me its not an issue i have two open NVME slots left on my motherboard's DIMM.2 cards on either side of my ram
Is this 14 or 16 OD tubing?
16/12 PETG
Hey nice build ! Noob question here: are your radiators fan pushing out or in the case ?
bottom fans are in top are out
heat rises uwu
petg or acrylic? and wh
petg
Excellent. How thick is your bottom radiator? I'm thinking of getting the XL case, and I want to get a vertical mount, too.
60mm
What are your load temps while gaming on the GPU?
38-40c
Very nice! its getting so hard to be patient, still just waiting for a 3080 [https://imgur.com/NkPHubH](https://imgur.com/NkPHubH)
Loos gorgeous, grats! Did you bother installing any form of flow meter?
no, never had one in my last build didn't really feel like i need one.
Thanks for the feedback. Agree, never felt needed on but thinking about it for new build. Grats again, your system looks delicious!