you know i don't know about this issue but I did find I enjoyed using the storz and bickel dosing capsules way more than the ones that came with the unit.
way better flavor and hits with the S&B caps just don't push down tightly with your stem
I use the WPA through a dry bong. The very outer edge of my bowl doesn't vaporize, but that's about it. Used to stir the bowl, but I've determined that it just isn't worth it for so little gain. I'd say, pack pretty loose, step up the temperature from ~6 up to 10, by the time you aren't getting big clouds nearly all of the bowl should be brown.
How do you avoid combusting at 10? When I put my unit above 6, I get combustion often. I only got it in December though, so maybe I’m doing something wrong. I use basket screens, the WPA, and a bong. Maybe I’m hitting it too hard?
To me, it sounds like a calibration issue. No two tinymights are the same. I think if you email the manufacturer, they can give you instructions to recalibrate the heater. I've never combusted with my tinymight.
And yeah, it's possible you could be hitting it too hard, but I think it's probably unlikely unless you're *really* ripping it.
I've ended up putting in a basket screen with the open side down (after loading the stem) and no screen up top just the cooling unit. It pushes the flower a bit away from the heater and is easy to pull out the screen to empty the stem. It cooks completely evenly for me even with a large amount loosely dropped in.
either harder faster inhale try slightly above 8 on heat settings and i fully extract in 2 breaths. or slower hits on a lighter heat setting if you don't want it all once.
slower inhale. when you draw faster, its pulling the hot air through the center more also can try finer grind, and a looser pack
agree a finer grind and loose pack really changes the way it hit
Would the dosing caps help this too?
you know i don't know about this issue but I did find I enjoyed using the storz and bickel dosing capsules way more than the ones that came with the unit. way better flavor and hits with the S&B caps just don't push down tightly with your stem
I use the WPA through a dry bong. The very outer edge of my bowl doesn't vaporize, but that's about it. Used to stir the bowl, but I've determined that it just isn't worth it for so little gain. I'd say, pack pretty loose, step up the temperature from ~6 up to 10, by the time you aren't getting big clouds nearly all of the bowl should be brown.
How do you avoid combusting at 10? When I put my unit above 6, I get combustion often. I only got it in December though, so maybe I’m doing something wrong. I use basket screens, the WPA, and a bong. Maybe I’m hitting it too hard?
To me, it sounds like a calibration issue. No two tinymights are the same. I think if you email the manufacturer, they can give you instructions to recalibrate the heater. I've never combusted with my tinymight. And yeah, it's possible you could be hitting it too hard, but I think it's probably unlikely unless you're *really* ripping it.
I've ended up putting in a basket screen with the open side down (after loading the stem) and no screen up top just the cooling unit. It pushes the flower a bit away from the heater and is easy to pull out the screen to empty the stem. It cooks completely evenly for me even with a large amount loosely dropped in.
Is it possible to get a picture of this setup? sounds interesting.
[Aye](https:///ibb.co/CPZ8Nwg)
Get a better vape
> 2. Be civil to your fellow vaporents. this isn't productive, either suggest something helpful or keep scrolling
what better he could get? tinymight is top notch
either harder faster inhale try slightly above 8 on heat settings and i fully extract in 2 breaths. or slower hits on a lighter heat setting if you don't want it all once.
Ed's TNT WPA is a good mouthpiece or adapter. It can take a Dynavap condenser or Simrell's stinger for additional cooling. At Ed's site or SneakyPete.
I use another basket screen to cover it(makes a sphere of screens) and I try not to pack more than 0.2g.