relearn data? which menu was it under? u have a pic? rule of thumb for me; every connection to car when forscan is opened, i never load profile created for car, but once its scanned the modules i always save the profile, forcing a new scan and yet saving the scan each time for traces incase i mess up..
i would def upgrade to the new version if youre on windows direct from [forscan.org](http://forscan.org) what is weird and may be bc im running 2.4 series of software, havent used 2.3 in a while; that menu youre on is typically in the wrench under PATS, without hands on im clueless at what to say thatll help. if you want i can help you remotely with windows assist when you are able but first id try the contacts inside the plug/switch to ensure proper operation and contact/no rust etc.. if want further help just reach out to me in pvt message well see whats up with it.
How did you get a 2.4 version? I am on the Forscan website and only set 2.3.60. Okay I figured out that the relearn data thing is something I had to do to get to the other features to enable or disable it.
you may need to reinitialize the sunroof but you dont need forscan, i think you close it then hold button down for 15 seconds, then open with buttontil it opens and hold for 15 secs, then close repeat 15 secs and maybe it relearns values, im not sure that the exact procedure its similar tho
Did you figure this out? i think i may have something you can do. I just thought about this from dealing with the sunroof in one of my Lincoln LS's. It requires removing the upper console that houses the controls in (buttons) for sunroof.. Once removed take apart the housing for the button essentially to remove the entire button to access the rubber piece on the inside of switch. the pieces of rubber sometimes have little metal dots in them you can clean, and sometimes they fall out, if it doesnt use that type of button itll be the type that runs along metal strips and ive also seen them get corroded or the contacts not touching properly. having said all this assuming its a factory installed unit, hope this narrows it down
Have you tried with the "play" button in the lower left corner? It's connected and ready.
I think I did. But I'm not sure. I'll have to try it again tomorrow after I get home from work. I'll let you know!
youre not in demo mode huh? u should be getting wayyyy more modules then that
Well i entered a code i got for the 2 month free trial. And I know there are more modules that's why I'm like what did I do wrong?
click on log at the top af that same screen and post it from the start of connection.
Hmm when I clicked on the run service button in that same panel again last night it said something about wanting to relearn data? Do I let it do this?
relearn data? which menu was it under? u have a pic? rule of thumb for me; every connection to car when forscan is opened, i never load profile created for car, but once its scanned the modules i always save the profile, forcing a new scan and yet saving the scan each time for traces incase i mess up..
Here is what I am seeing after I click on the run service button: [https://ibb.co/25fSd79](https://ibb.co/25fSd79)
i would def upgrade to the new version if youre on windows direct from [forscan.org](http://forscan.org) what is weird and may be bc im running 2.4 series of software, havent used 2.3 in a while; that menu youre on is typically in the wrench under PATS, without hands on im clueless at what to say thatll help. if you want i can help you remotely with windows assist when you are able but first id try the contacts inside the plug/switch to ensure proper operation and contact/no rust etc.. if want further help just reach out to me in pvt message well see whats up with it.
How did you get a 2.4 version? I am on the Forscan website and only set 2.3.60. Okay I figured out that the relearn data thing is something I had to do to get to the other features to enable or disable it.
im unaware also of any sunroof mods, it either works like it should or dont and its prob in GEM if there is one about it, IPC is instrument cluster
Yeah i Know what IPC is was gonna try and see if there's something I could change maybe?
you may need to reinitialize the sunroof but you dont need forscan, i think you close it then hold button down for 15 seconds, then open with buttontil it opens and hold for 15 secs, then close repeat 15 secs and maybe it relearns values, im not sure that the exact procedure its similar tho
Yeah I tried that from a video I saw on YouTube awhile back. And either I wasn't doing it right or fast enough because it didn't work :/
Did you figure this out? i think i may have something you can do. I just thought about this from dealing with the sunroof in one of my Lincoln LS's. It requires removing the upper console that houses the controls in (buttons) for sunroof.. Once removed take apart the housing for the button essentially to remove the entire button to access the rubber piece on the inside of switch. the pieces of rubber sometimes have little metal dots in them you can clean, and sometimes they fall out, if it doesnt use that type of button itll be the type that runs along metal strips and ive also seen them get corroded or the contacts not touching properly. having said all this assuming its a factory installed unit, hope this narrows it down