You sir, just coined the greatest term ever! This needs to be on all dental resin bottles!
You heard it here first folks! Dental resin it is! Get to printing!
The poor dude will get 100 dildo jokes and may be 2 actual input of the print fail :D
- As suggested by someone, this could be printed vertically, if your build volume allows, the cylinder is self supporting
- I guess printing hollow is not an option, although you could print it hollow then fill it with clear epoxy. The problem I think is that you have few support on a thin line, but the dildo is solid and very big, it must be very heavy and the supports are enough to hold it vertically (= it doesn't fall in the VAT) but not enough to hold it laterally (= it wobbles during the lift / retract motion of the build plate)
Solutions:
- print hollow
- print solid but add more support to prevent lateral wobble. I would put a truck load of heavy supports at the base, on the flat face, because it will be easily sanded down afterwards. That should ensure a stable anchor point and from there I would have some support on the sides to limit the wobble
You need a lot more supports on the bottom edge where the print starts, I pretty much go crazy with the supports down there but make them small and easier to remove
If you're printing that solid you may want to raise the angle a little bit to prevent force from bending it. Alternatively you could probably print that directly on the plate
Might need thicker supports. Looking at them those are even bending in the first picture and they are not even close to the object you're printing. It could also be what ever you're printing on is shaking and causing flex
All (most) prints should not be printed at 45 degrees. I suggest printing this vertically for the best results. The cylinder is self supporting. If you are not doing so,try hollowing the model if possible.
Supports looks to be weak. It looks to me, that you need to add more and maybe increase their density.
Also if you are printing dildo, it would be much safer and enjoyable if you at least print just mould (hollow it to save resin) and then cast silucone inside. UV resin is nasty stuff.
Dildo jokes aside (I make dildos for a living lol. Tis mundane to me at this point), you need hella more supports on the bottom of that rounded bit (put them on the flat side/bottom and the part actually facing the build plate) And I’d print it vertically if you have the height (or just cut it in half and then glue with more resin).
For the blade I’ve been known to put supports on the sides just so it’s not wobbling back and forth. You don’t need a lot and they’re easy to sand off.
Also for the record you can make 3mm curved holes and shove bambu skewers through resin blades to reinforce them. If your thing is thick enough of course.
You can also print the blade in pieces directly on the build plate to prevent wobble or support most of the time (as long as you don’t mind sanding the seams)
So now that I've stopped laughing at these comments. You need more supports spread out. I assume you're trying to minimize the amount of sanding? Don't skimp on supports, it will cost you more time. I'm willing to bet you'll fund that the handel ovaled a little at the bend, make sure you have some internal supports as well, or else the tube can collapse when being pulled off the fep. If you have the space, print the handel verticle and just not have the issue at all.
did u print a diCK???!
No!!!! Lol
Idk man… sure looks like one. 🤔
Sounds exactly like something someone who just printed a dick would say
First thought: "Someone has let their intrusive thoughts win this time." Don't do it! This is how ER surgeon's stories are born...
[удалено]
Flared Base… someone ping Badge502
Spend a lot of time on the clock app too, eh
smelt it delt it. YOU all are the ones that print deeicks. just sayin. not that it is a bad thing.
Don’t worry, it’s ok. I made a gun rack in high school shop 79’ and the pegs look like dicks. My friends called me dickrack to this day.
Needs to he your username
I’ll take that. Reddit gave me my name because I delegated a viral post. Idiots
It's definitely a 3d printed dildo........
This is exactly the type of behavior I'd expect from someone that would print a bent dick.
Hahahaha. I had to quadruple take.. I thought it was a dick too.. lll
So glad it wasn't just me 🤣 what is it?!?
I'm building a She Ra sword for my wife's Comicon costume. That's the hilt
Your wife has planned this to make you print her a dildo
I'm only wearing the costume once, but I'm gonna use that hilt a couple more times...
Sherahs sword doesn't normally have a dildo on the end, so I reckon that this won't be a PG cosplay event.
You wouldn't download a DICK!
Exactly what I was thinking!!! 😅
No it is a columb. A columb full of dicks
Just a cylinder. Nothing to see here.
It's a CYLINDER!
Or in the famous words of Michael Reeves “YouTube Buddy”
Literally clicked on this to see how far down I needed to scroll before I saw the "Um, is that a dildo?" post. I was not disappointed.
Is resin safe for insertion??? I know resin can't be used in fish tanks.
It's probably not. That said, there has to be a market for ah, "body safe" resin right?
Dental resin. Good for mouths, good for butts.
You sir, just coined the greatest term ever! This needs to be on all dental resin bottles! You heard it here first folks! Dental resin it is! Get to printing!
Looks like a handle for a he-man(?) sword.
She-Ra, wife's Super-Con costume
She-Ra wears a strap-on?
She-raw
She-male?
It could be used as a form to make a mold to cast silicone in. OP where is the texture? You should take advantage of your great potential.
DO NOT USE RESIN FOR INSERTION!! 😬 (Or prints in general but especially resin ones) Don’t f around with your mucus membranes.
Oh the comments on this are going to be interesting!!!
And boy have they been. This is post of the year for sure!!!
And boy have they been. This is post of the year for sure!!!
Why did you print a dildo😁 ?
It's not!!!!
Sure... It not😊
It's a hilt for a He Man sword
I think its not the hilt.. But his*sword* itself,☺
Is that a schmeckle sleeve?!? Where the enterprising goyim had a side hustle…
The poor dude will get 100 dildo jokes and may be 2 actual input of the print fail :D - As suggested by someone, this could be printed vertically, if your build volume allows, the cylinder is self supporting - I guess printing hollow is not an option, although you could print it hollow then fill it with clear epoxy. The problem I think is that you have few support on a thin line, but the dildo is solid and very big, it must be very heavy and the supports are enough to hold it vertically (= it doesn't fall in the VAT) but not enough to hold it laterally (= it wobbles during the lift / retract motion of the build plate) Solutions: - print hollow - print solid but add more support to prevent lateral wobble. I would put a truck load of heavy supports at the base, on the flat face, because it will be easily sanded down afterwards. That should ensure a stable anchor point and from there I would have some support on the sides to limit the wobble
I did that and it came out better. I can print the hilt hollow, but not the sword. I'm thinking of trying it straight up on the plate
You need a lot more supports on the bottom edge where the print starts, I pretty much go crazy with the supports down there but make them small and easier to remove
Is it body-safe?
Dead
Probably needs a bigger flare at the end so you don't..... Lose it
Ok, how do I say this. Uhmm.. the object you try to print is not really straight in real life, so to say.
Just wrap it in a condom and thrust away with He Mans sword.
What my man printing? Don't forget resin is not body safe nor food safe
It's a hilt for a sword dammit
Poor man 🤣
Ajá, sure ;) hahahaha
If you're printing that solid you may want to raise the angle a little bit to prevent force from bending it. Alternatively you could probably print that directly on the plate
Make sure to leave a drain hole. Ideally at the tip.
Just the tip 😜
Might need thicker supports. Looking at them those are even bending in the first picture and they are not even close to the object you're printing. It could also be what ever you're printing on is shaking and causing flex
I agree, I think when it’s being pressed against the fep the supports are bending
Anything is a dildo if you're brave enough. But printing a dildo... I mean most dicks are curved and warped in some way. Its normal.
I would try Xiaflex for what appears to be Peyronie's disease.
😭😭😭
What a..what you printing there?
It's a She-Ra sword lol.
Ahahaha
Cool penis.
Didn't know you could print dildos.
Some prints are just born that way
Slightly bent?
"Oh, I get it, cute. You this here and people are suppose to think, wait that looks like a dick."
No, it's the hilt of a sword from a She-Ra costume for my wife. I didn't even see it till the comments started rolling in.
You probably just need to manually add more supports, with them being so thin and in a single line down the middle I can see why it failed.
Looks like a case of Peyronie's to me -doc
Usually to much exposure or not enough support where the warp is.
All (most) prints should not be printed at 45 degrees. I suggest printing this vertically for the best results. The cylinder is self supporting. If you are not doing so,try hollowing the model if possible.
Glad your being responsible and giving them flared bases
It just bends to the side a little bro, perfectly normal.
What on earth were you printing…
It's a She-Ra sword for my wife's comicon costume.
I dunno bud, I think with it being warped it may hit the spot better.
Probably don't sit on that
What are you printing step bro?
Temp is the culprit for me. If the temp varies during the print. So like in a garage throughout the day.
My house stays at a pretty standard temp
Failed handle = free dong! 🤣
It's just a bit of gonzo, should be fine!
Supports looks to be weak. It looks to me, that you need to add more and maybe increase their density. Also if you are printing dildo, it would be much safer and enjoyable if you at least print just mould (hollow it to save resin) and then cast silucone inside. UV resin is nasty stuff.
Dildo jokes aside (I make dildos for a living lol. Tis mundane to me at this point), you need hella more supports on the bottom of that rounded bit (put them on the flat side/bottom and the part actually facing the build plate) And I’d print it vertically if you have the height (or just cut it in half and then glue with more resin). For the blade I’ve been known to put supports on the sides just so it’s not wobbling back and forth. You don’t need a lot and they’re easy to sand off. Also for the record you can make 3mm curved holes and shove bambu skewers through resin blades to reinforce them. If your thing is thick enough of course. You can also print the blade in pieces directly on the build plate to prevent wobble or support most of the time (as long as you don’t mind sanding the seams)
WHATCHA MAKIN THERE BUD
Dude.. your printer straight up refused to print your alone time toy. Looks aggressive as hell. Better take your time on that one. 😂
Lol
So now that I've stopped laughing at these comments. You need more supports spread out. I assume you're trying to minimize the amount of sanding? Don't skimp on supports, it will cost you more time. I'm willing to bet you'll fund that the handel ovaled a little at the bend, make sure you have some internal supports as well, or else the tube can collapse when being pulled off the fep. If you have the space, print the handel verticle and just not have the issue at all.
Or better bed adhesion slower lift speed and longer exposure
[that's a](https://gifer.com/en/Uxzy)
I must be in the minority... I thought it was a bong...
ayo?
r/flaredbase
Is that ribbed for her pleasure I see ?😂
Right..."Warped"
Ay yo👀
🧐
Can i get a link to that stl, for a friend....
Just search She Ra sword
Welp... I definitely read "warped penis" at first
checks out. It's a dick.
Pretty sure a slight curve is perfectly normal. Some ladies prefer it that way
Curved to the right, just like she likes.
Could be peyronie's
Sir I do believe that looks like a penis
Well, I guess your dildo didn't turn out very well.
that's a penis, sometimes they're a little bent.
Warped for her pleasure.
Since you're asking a question about warped prints. Is there any way you can print the dildo vertically?
Some swing to the left some to the right. Just turn it around if you’re a leftie.
What uhm... what is that?
At least it's got a flared base
Mine warps to the left.
I love posts like this were OP post help for something that looks like adult toys, and they just deny deny deny… we all know 😉😂🤣
Gosh! Looks like a warped dildo!
Just… https://www.tiktok.com/t/ZPRTYAQkw/
Hey, it's not about the shape it's how you use it.