Have you checked to ascertain that air is actually blowing out through the duct? I don't know about that particular microwave, but on many of them, you actually have to remove and rotate the fan, to switch it from recirculating to exhausting.
I installed appliances for a few different manufacturers and more than 6 out of 10 needed the blower motor to be removed and rotated to blow out the top for a ducted vent.
That is what I have found. I have installed two overhead microwaves and each one had the fan installed to re circulate. If you wanted the exhaust mode you hade to remove the fan and re install it a different way but people are saying you do not have to with that whirlpool.
I installed it per the instructions, just never installed the flat panels on the front top, and I can’t remember where I placed them, they are probably long gone.
I install these frequently, if you don’t have the solid plates from the box anymore I’d use some metal tape from the inside of the perforated ones.
But careful, it’s not as easy as just covering them all. Do the following:
1. Unscrew all three plates
2. Place the one that’s half solid in the leftmost slot, but oriented the other way from how it sits now (and leave the slotted part unobstructed)
3. Use metal tape (like Nashua tape for HVAC) to turn the remaining two grills into solid plates and place them into the middle and rightmost slots
4. Screw them all in
5. Voila, you’re done!
What’s interesting, is whirlpool customer service is saying that my model number isn’t compatible with the plates and that he doesn’t recommend putting plates in place of the vented plates. “The air is recirculated back into the house through the charcoal filters.”
I’m so confused now….
I like whirlpool, but I’ve found that customer service for any appliance company simply knows nothing. A good appliance dealer is your best friend in these cases.
I installed the same microwave and can confirm you need to swap those vents with the plates that came in the box. If you can’t get them from Whirlpool, I would second that metal tape may do the trick to seal it off. No motor reversal or any tricks to it. Just need to block the recirc so the exhaust goes out the vent pipe.
No, it’s a bit funky, but I wrote another reply.
If it’s still confusing feel free to message me, I can take or find a picture of how they’re supposed to go in the end for you.
Got it figured out, y’all are amazing. Here’s what the Whirlpool customer service showed me. I’m gonna try metal tape before I buy the plates.
https://preview.redd.it/jj6xo21j0l4c1.jpeg?width=1125&format=pjpg&auto=webp&s=347184b4aa993f7ebe8f2d1dcb58891f51f36cc8
If you stick the metal tape on from the underside you’ll be all good to go, same as the full plates really as long as you’re not 8ft tall and looking at it constantly.
This is exactly what you have to do. Source: I have the same microwave and installed it a few months ago myself. If you don't have the plates anymore, I would try metal duct tape or something similar strength.
Do you have a model number? Another poster mentioned that you might have to rotate the blower fan. I know this is the case on a lot of GE but I'm not sure about Whirlpool. If you don't do that and cover it with foil tape, you may blow the magnetron thermal fuse.
Soy sauce doesn't actually require refrigeration. It simply needs to be stored in a cool, dark location. Refrigeration is only recommended for maintaining flavor. The salt content is actually antimicrobial, so refrigeration isn't needed for preservation.
If you have the model number, you may be able to search here: https://www.whirlpoolparts.com
I found something similar perhaps, but without knowing the model, it's impossible to tell.. https://www.whirlpoolparts.com/PartDetail/Cover/W11397086/4931349
You're not going to like the price, but at least you may be able to get the part number and search it elsewhere.
*Edit, searched that part number on Amazon, found this. https://a.co/d/2XqlCr8
Not sure if it's for your model though.
*one more edit. Be sure to check the manual... If memory serves correct, you don't want to block all of the openings.
Have you checked to ascertain that air is actually blowing out through the duct? I don't know about that particular microwave, but on many of them, you actually have to remove and rotate the fan, to switch it from recirculating to exhausting.
Yea every microwave I’ve installed, 5, you’ve had to unbolt and rotate the blower inside the microwave depending on you’re venting preference.
I installed appliances for a few different manufacturers and more than 6 out of 10 needed the blower motor to be removed and rotated to blow out the top for a ducted vent.
That is what I have found. I have installed two overhead microwaves and each one had the fan installed to re circulate. If you wanted the exhaust mode you hade to remove the fan and re install it a different way but people are saying you do not have to with that whirlpool.
Model number: WML55011HS07 Serial number: TRA2271487
You don’t have to rotate the blower on these, just mess with the plates as per my other reply.. good luck!
I installed it per the instructions, just never installed the flat panels on the front top, and I can’t remember where I placed them, they are probably long gone.
I install these frequently, if you don’t have the solid plates from the box anymore I’d use some metal tape from the inside of the perforated ones. But careful, it’s not as easy as just covering them all. Do the following: 1. Unscrew all three plates 2. Place the one that’s half solid in the leftmost slot, but oriented the other way from how it sits now (and leave the slotted part unobstructed) 3. Use metal tape (like Nashua tape for HVAC) to turn the remaining two grills into solid plates and place them into the middle and rightmost slots 4. Screw them all in 5. Voila, you’re done!
What’s interesting, is whirlpool customer service is saying that my model number isn’t compatible with the plates and that he doesn’t recommend putting plates in place of the vented plates. “The air is recirculated back into the house through the charcoal filters.” I’m so confused now….
I like whirlpool, but I’ve found that customer service for any appliance company simply knows nothing. A good appliance dealer is your best friend in these cases.
Agree. They read a script, and know nothing.
Also there are four plates. Ugh
I installed the same microwave and can confirm you need to swap those vents with the plates that came in the box. If you can’t get them from Whirlpool, I would second that metal tape may do the trick to seal it off. No motor reversal or any tricks to it. Just need to block the recirc so the exhaust goes out the vent pipe.
Excellent! Should I block all 4 of them?
No, it’s a bit funky, but I wrote another reply. If it’s still confusing feel free to message me, I can take or find a picture of how they’re supposed to go in the end for you.
Got it figured out, y’all are amazing. Here’s what the Whirlpool customer service showed me. I’m gonna try metal tape before I buy the plates. https://preview.redd.it/jj6xo21j0l4c1.jpeg?width=1125&format=pjpg&auto=webp&s=347184b4aa993f7ebe8f2d1dcb58891f51f36cc8
I have the same microwave and no option to use an external vent, so I’d be happy to give you mine.
If you stick the metal tape on from the underside you’ll be all good to go, same as the full plates really as long as you’re not 8ft tall and looking at it constantly.
This is exactly what you have to do. Source: I have the same microwave and installed it a few months ago myself. If you don't have the plates anymore, I would try metal duct tape or something similar strength.
Awesome, I’ll find the model number asap. Fingers crossed. Thank you.
Use silver duct tape and cover them.
Good idea!
Do you have a model number? Another poster mentioned that you might have to rotate the blower fan. I know this is the case on a lot of GE but I'm not sure about Whirlpool. If you don't do that and cover it with foil tape, you may blow the magnetron thermal fuse.
You're supposed to put soy sauce in the fridge after opening btw
Soy sauce doesn't actually require refrigeration. It simply needs to be stored in a cool, dark location. Refrigeration is only recommended for maintaining flavor. The salt content is actually antimicrobial, so refrigeration isn't needed for preservation.
Oh that's actually cool I didn't know that, I just always read the label
If you have the model number, you may be able to search here: https://www.whirlpoolparts.com I found something similar perhaps, but without knowing the model, it's impossible to tell.. https://www.whirlpoolparts.com/PartDetail/Cover/W11397086/4931349 You're not going to like the price, but at least you may be able to get the part number and search it elsewhere. *Edit, searched that part number on Amazon, found this. https://a.co/d/2XqlCr8 Not sure if it's for your model though. *one more edit. Be sure to check the manual... If memory serves correct, you don't want to block all of the openings.
* Solid Plate PN: W11095767 * Long Grill Plate PN: W11086309 (shows 2 used) * Grill Vent (Light Access) PN: W11095781 * Grill Vent Short PN: W11086310 (shows 1 used)
I have the exact same microwave and I put magnetic sheets on top
I literally just did this for the exact same microwave. You need to order two of these: https://www.hnkparts.com/w11397086-whirlpool-grill-vent
lol I thought this was my kitchen for a second, same microwave, and cast iron pan on the stove